Slippery Board`

General discussions about windsurfing: equipment, setup tips, problems, where to go, where you should have been, lost and found
Post Reply
User avatar
BigD
Website Donor
Website Donor
Posts: 141
Joined: Thu May 13, 2004 11:51 pm
Location: Tsawwassen
Been thanked: 9 times

Slippery Board`

Post by BigD »

I've got a Fanatic Freewave 86L and I noticed this weekend at Nitnat that the area between the foot straps is a bit slippery. Any one have a good method to easily add some grip?

[smilie=wizard.gif]
User avatar
thankgodiatepastafobreaky
Posts: 512
Joined: Tue Jul 13, 2004 5:55 pm
Location: Gordon's
Been thanked: 2 times
Contact:

Post by thankgodiatepastafobreaky »

sex wax :?
curses - foiled again!
KayakDoc
Posts: 145
Joined: Tue May 08, 2007 12:35 am

Post by KayakDoc »

BigD. I have some acrylic non-skid “powder” from Resin Research. It is a new product that was given to me to test. It is fantastic. Sand your board, spread a little resin and a sprinkle of the non-skid and you will no longer slip. I am away next week, but I will be back in Victoria the week after and I will pass on some if you want it. Let me know. PS As long as you keep your damn dragon under control.
User avatar
downwind dave
Website Donor
Website Donor
Posts: 1469
Joined: Thu Apr 29, 2004 9:05 am
Location: Cobble Hill

Post by downwind dave »

i tried out a can of monster traction spray, 22$ at Island Longboards. it worked ok on my sup board and skate deck but on the WS board i found it not quite gritty enough.
User avatar
thankgodiatepastafobreaky
Posts: 512
Joined: Tue Jul 13, 2004 5:55 pm
Location: Gordon's
Been thanked: 2 times
Contact:

Post by thankgodiatepastafobreaky »

too gritty and you will be bleeding. That happened to me more than once on windsurfers.
curses - foiled again!
KayakDoc
Posts: 145
Joined: Tue May 08, 2007 12:35 am

Post by KayakDoc »

This Resin Research ground acrylic is fantastic. I used an acrylic nonskid from Fiberglass Hawaii and my toes got eaten. The Resin Research acrylic has much smaller particles and is not as abrasive as the FH stuff. Also a very light post cure sanding helps as well.
User avatar
windaddiction
Posts: 113
Joined: Fri Dec 12, 2003 3:33 pm
Location: victoria

Post by windaddiction »

sugar and resin works well too if your looking for something a little sweeter!
User avatar
BigD
Website Donor
Website Donor
Posts: 141
Joined: Thu May 13, 2004 11:51 pm
Location: Tsawwassen
Been thanked: 9 times

slippery

Post by BigD »

Thanks everyone for the info. Kayakdoc, I live in Tsawwassen, hope to make it back to Nitnat near the end of Aug, maybe we can meet up then.

Cheers,
Dallas
User avatar
SmallWaveSteve
Posts: 250
Joined: Mon Aug 08, 2011 8:48 am

Post by SmallWaveSteve »

You can also get spray on grip from West marine
User avatar
KUS
Website Donor
Website Donor
Posts: 2781
Joined: Fri Jan 02, 2004 8:32 am
Been thanked: 2 times

Re: Slippery Board`

Post by KUS »

BigD wrote:I've got a Fanatic Freewave 86L and I noticed this weekend at Nitnat that the area between the foot straps is a bit slippery. Any one have a good method to easily add some grip?
buy a new board :roll: D Dood :idea: DING! Rock, no... paper.....ah shucks go for scissors :!:
Wish less, sail more!!
Vancouver Island Windsports
Chinook /Takuma /KA Australia (Tribal) /Aztron

You're either in or in the way....
Doing things the hard way since 1963....
User avatar
BigD
Website Donor
Website Donor
Posts: 141
Joined: Thu May 13, 2004 11:51 pm
Location: Tsawwassen
Been thanked: 9 times

new board

Post by BigD »

New board, that's a whole 'nother thread! I think I'm gonna learn duck jibes before I get a new board since I'm likely to take the nose off... :roll:
KayakDoc
Posts: 145
Joined: Tue May 08, 2007 12:35 am

Post by KayakDoc »

BigD, Send me your contact information if you like. I may be passing through Tsawwassen and could drop some off. Reluctant to send unidentifiable white powder in the mail.
Post Reply